|
Size: 4263
Comment:
|
Size: 4785
Comment: Bullets
|
| Deletions are marked like this. | Additions are marked like this. |
| Line 1: | Line 1: |
| ## page was renamed from GearFaq | |
| Line 2: | Line 3: |
| {{{ Contents |
|
| Line 5: | Line 4: |
| 1. General description 2. Variants (original, 70's reissue, 90's reissue) 3. Theory of operation 4. Other (Kendrick, Texotica, G-Spring, etc.) 5. Mods }}} 1. General Description |
<<TableOfContents()>> == General Description == |
| Line 17: | Line 12: |
| 2. Variants | == Variants == |
| Line 19: | Line 14: |
| 1961-1966 - Handwired, 6K6 powertube, Hammond reverb pan (61-64)Gibbs reverb pan(64-66), appeared in every cosmetic variation in that era. | * 1961-1966 - Handwired, 6K6 powertube, Hammond reverb pan (61-64)Gibbs reverb pan(64-66), appeared in every cosmetic variation in that era. * 1976-1978 - Handwired, 6V6 power tube, Accutronics reverb pan, silverface cosmetics. Super rare, I think somebody here owns one. I've never seen one is person. I think they are just the same as 61-66... * 1994- Present Reissue - PCB, 6V6 powertube, Accutronics pan, Blonde/oxblood, brown/wheat, black/silver, tweed. |
| Line 21: | Line 18: |
| 1976-1978 - Handwired, 6V6 power tube, Accutronics reverb pan, silverface cosmetics. Super rare, I think somebody here owns one. I've never seen one is person. I think they are just the same as 61-66... | == Theory of Operation == |
| Line 23: | Line 20: |
| 1994- Present Reissue - PCB, 6V6 powertube, Accutronics pan, Blonde/oxblood, brown/wheat, black/silver, tweed. | (it's based on the Fender service manual A block diagram is probably a good idea. This is pretty detailed and would put most people to sleep, but the techs need to know this) |
| Line 25: | Line 22: |
| 3. Theory of Operation (it's based on the Fender service manual A block diagram is probably a good idea) | === Reverb Drive Path === |
| Line 27: | Line 24: |
| a. Reverb Drive Path The first stage uses one half of the 12AT7 and provides a voltage gain A voltage divider reduce the signal and then it is sent to the Dwell , which determines the amount of signal sent to the reverb drive circuit. |
The first stage uses one half of the 12AT7 and provides a voltage gain A voltage divider reduce the signal and then it is sent to the Dwell control (250K pot), which determines the amount of signal sent to the reverb drive circuit. |
| Line 35: | Line 30: |
| The 6K6GT power tube supplies power necessary to drive the reverb transformer. | The 6K6GT power tube supplies power necessary to drive the reverb transformer. Although a 6V6 driver tube is used in the 90's reissue, the power tube biasing resistor is the same value used by the 6K6 circuit. This larger value causes the 6V6 to be overbiased (cold), limiting output power and causing early distortion. |
| Line 37: | Line 32: |
| b. Reverb Recovery Path | === Reverb Recovery Path === |
| Line 39: | Line 34: |
| The footswitch turns the reverb on and off by grounding the input to the reverb recovery circuit. The senses the reverb return signal and amplifies it with a gain of about 37. | The footswitch turns the reverb on and off by grounding the input to the reverb recovery circuit. One half of the 12AX7 tube amplifies the reverb return signal. |
| Line 41: | Line 36: |
| The Tone control (R17) attenuates the high frequencies above 3kHz, through C9. C10 provides a slight bass roll off | The Tone control attenuates the high frequencies ( I can run a PSpice simulation to illustrate the effect of the tone control settings) |
| Line 43: | Line 38: |
| which is affected by the position of the Mix control in relation to the input impedance of the guitar amplifier. | === Dry Signal Path === |
| Line 45: | Line 40: |
| c. Dry Signal Path | 1/2 of the 12AX7 is used as a cathode follower buffer amplifier for the dry signal. The input to the dry signal path is directly in parallel with the reverb drive path! |
| Line 47: | Line 42: |
| Cathode follower, unity gain buffer amplifier for the dry signal. The input to the dry signal path is directly in parallel with the reverb drive path! | === Mixer Circuit === |
| Line 49: | Line 44: |
| C11 is a non-polarized, metalized polyester film capacitor, which is located across the high voltage transformer | The Mixer circuit is a simple resistive mixer consisting of a 50K linear taper pot. One side of the pot is fed by the dry signal path and the other is fed by the reverb recovery circuit. The control is essentially a pan pot that favors the dry signal at 0 and the wet signal when set to 10. This is in contrast to the Reverb control used in the combo amps, which simply controls the amount of reverb recovery signal mixed into the dry signal path. |
| Line 51: | Line 46: |
| secondary, suppresses EMI frequencies from 20kHz to 30mHz. This is necessary to conform to modern day NEMKO | As the Mixer control is turned up from zero, additional resistance is placed in series with the output of the dry signal path (the cathode follower). This additional resistance forms a low-pass RC filter with the capacitance of the cable used to connect the reverb unit to the amplifier. The resultant filter removes high frequencies from the dry signal, and effect known as 'tone suck'. (I can run PSpice simulations to illustrate the amount of high-frequency loss in the dry signal caused by the Mixer control settings) |
| Line 53: | Line 48: |
| safety requirements. | === Output Buffer Circuit (70's reissue only) === |
| Line 55: | Line 50: |
| The pot mounting brackets are all connected together via traces on the circuit board. The trace connects to the star | A 4th preamp tube is added. A cathode follower is used to isolate the Mixer output from the guitar cable/amplifier load imedance. The goal is to prevent tonal variations (tone suck) as the Mixer control is turned up. The buffer prevents the patch cable capacitance from interacting with the Mixer control resistance, mitigating the RC filtering effect. |
| Line 57: | Line 52: |
| audio ground through R22, R22 places 15 ohms of resistance between audio ground and the pot mounting brackets. | == Issues == |
| Line 59: | Line 54: |
| This is done for two reasons. Fist, with the circuit board installed, the pot brackets are physically connected to | [description of tone suck here] |
| Line 61: | Line 56: |
| chassis/earth ground. R22 isolates audio ground from earth ground through the pot brackets. This eliminates internal | [description of ground loop; components added to the reissue that mitigate internal loops] |
| Line 63: | Line 58: |
| ground loops. Secondly, when the circuit board is removed for repair and testing, R22 provides a ground reference | == Others == |
| Line 65: | Line 60: |
| (15 ohms) for the pot brackets. R23 places 15 ohms of resistance between audio ground and chassis/earth ground. | Kendrick, Texotica, Gomez, etc. |
| Line 67: | Line 62: |
| This minimizes hum by eliminating ground loops internally and externally when connection with other units. R22 and | Kits, both tube and solid-state |
| Line 69: | Line 64: |
| R23 are Flame Proof/Fusible resistors. If excessive current flows through theses resistors, they will not burn, they will | == Honorable Mention == |
| Line 71: | Line 66: |
| simply open. | The Fender amps that have a 3-knob reverb circuit (Vibro-King, Dual Professional) |
| Line 73: | Line 68: |
| CR5 & 6 (across R23) provide an important safety feature. IF the guitar amp chassis becomes electrified, current will | Modules that can be added to a combo amp. |
| Line 75: | Line 70: |
| flow through the coax cable to the power supply ground of the Fender Reverb unit. The current will seek earth ground through R23. When R23 opens, the earth ground connection is broken. This will electrify the reverb unit’s ground and |
Pedals that allege to duplicate the sound of the 6G15 circuit The Fender amps that have a 3-knob reverb circuit |
Fender 6G15 Reverb Unit
Contents
General Description
The Fender Reverb Unit (6G15) was a tube, spring reverb-equipped effects unit made by Fender. The Reverb Unit was originally introduced in 1961. It was discontinued in 1966 and was replaced by a solid-state model, the FR1000.[[http://en.wikipedia.org/wiki/Fender_Reverb_Unit#cite_note-1|[1]]] The unit features three controls: Dwell, Mix and Tone and is run by two pre-amp tubes and a power tube. Physically the unit looks like a small ampilfier head and since the early '60s the unit has become synonymous with surf music.
OK, so I stole this from Wikipedia. Sue me.
Variants
- 1961-1966 - Handwired, 6K6 powertube, Hammond reverb pan (61-64)Gibbs reverb pan(64-66), appeared in every cosmetic variation in that era.
- 1976-1978 - Handwired, 6V6 power tube, Accutronics reverb pan, silverface cosmetics. Super rare, I think somebody here owns one. I've never seen one is person. I think they are just the same as 61-66...
- 1994- Present Reissue - PCB, 6V6 powertube, Accutronics pan, Blonde/oxblood, brown/wheat, black/silver, tweed.
Theory of Operation
(it's based on the Fender service manual A block diagram is probably a good idea. This is pretty detailed and would put most people to sleep, but the techs need to know this)
Reverb Drive Path
The first stage uses one half of the 12AT7 and provides a voltage gain A voltage divider reduce the signal and then it is sent to the Dwell control (250K pot), which determines the amount of signal sent to the reverb drive circuit.
The reverb drive circuit consists of the second half of the 12AT7 preamp tube, a high-pass filter, a 6K6 power tube, and the reverb transformer.
The signal is amplified by the 12AT7 and sent through an RC high-pass filter which rolls off low frequencies below 300Hz.
The 6K6GT power tube supplies power necessary to drive the reverb transformer. Although a 6V6 driver tube is used in the 90's reissue, the power tube biasing resistor is the same value used by the 6K6 circuit. This larger value causes the 6V6 to be overbiased (cold), limiting output power and causing early distortion.
Reverb Recovery Path
The footswitch turns the reverb on and off by grounding the input to the reverb recovery circuit. One half of the 12AX7 tube amplifies the reverb return signal.
The Tone control attenuates the high frequencies ( I can run a PSpice simulation to illustrate the effect of the tone control settings)
Dry Signal Path
1/2 of the 12AX7 is used as a cathode follower buffer amplifier for the dry signal. The input to the dry signal path is directly in parallel with the reverb drive path!
Mixer Circuit
The Mixer circuit is a simple resistive mixer consisting of a 50K linear taper pot. One side of the pot is fed by the dry signal path and the other is fed by the reverb recovery circuit. The control is essentially a pan pot that favors the dry signal at 0 and the wet signal when set to 10. This is in contrast to the Reverb control used in the combo amps, which simply controls the amount of reverb recovery signal mixed into the dry signal path.
As the Mixer control is turned up from zero, additional resistance is placed in series with the output of the dry signal path (the cathode follower). This additional resistance forms a low-pass RC filter with the capacitance of the cable used to connect the reverb unit to the amplifier. The resultant filter removes high frequencies from the dry signal, and effect known as 'tone suck'. (I can run PSpice simulations to illustrate the amount of high-frequency loss in the dry signal caused by the Mixer control settings)
Output Buffer Circuit (70's reissue only)
A 4th preamp tube is added. A cathode follower is used to isolate the Mixer output from the guitar cable/amplifier load imedance. The goal is to prevent tonal variations (tone suck) as the Mixer control is turned up. The buffer prevents the patch cable capacitance from interacting with the Mixer control resistance, mitigating the RC filtering effect.
Issues
[description of tone suck here]
[description of ground loop; components added to the reissue that mitigate internal loops]
Others
Kendrick, Texotica, Gomez, etc.
Kits, both tube and solid-state
Honorable Mention
The Fender amps that have a 3-knob reverb circuit (Vibro-King, Dual Professional)
Modules that can be added to a combo amp.
Pedals that allege to duplicate the sound of the 6G15 circuit The Fender amps that have a 3-knob reverb circuit
